Young's modulus

Young's modulus
a coefficient of elasticity of a substance, expressing the ratio between a stress that acts to change the length of a body and the fractional change in length caused by this force.
[1860-65; named after Thomas YOUNG, who derived it]

* * *

      numerical constant, named for the 18th-century English physician and physicist Thomas Young (Young, Thomas), that describes the elastic (elasticity) properties of a solid undergoing tension or compression in only one direction, as in the case of a metal rod that after being stretched or compressed lengthwise returns to its original length. Young's modulus is a measure of the ability of a material to withstand changes in length when under lengthwise tension or compression. Sometimes referred to as the modulus of elasticity, Young's modulus is equal to the longitudinal stress divided by the strain. Stress and strain may be described as follows in the case of a metal bar under tension.

 If a metal bar of cross-sectional area A is pulled by a force F at each end, the bar stretches from its original length L0 to a new length Ln. (Simultaneously the cross section decreases.) The stress is the quotient of the tensile force divided by the cross-sectional area, or F/A. The strain or relative deformation is the change in length, LnL0, divided by the original length, or (LnL0)/L0. (Strain is dimensionless.) Thus Young's modulus may be expressed mathematically as

      Young's modulus = stress/strain = (FL0)/A(LnL0).

      This is a specific form of Hooke's law of elasticity. The units of Young's modulus in the English system are pounds per square inch (psi), and in the metric system newtons per square metre (N/m2). The value of Young's modulus for aluminum is about 1.0 × 107 psi, or 7.0 × 1010 N/m2. The value for steel is about three times greater, which means that it takes three times as much force to stretch a steel bar the same amount as a similarly shaped aluminum bar.

      Young's modulus is meaningful only in the range in which the stress is proportional to the strain, and the material returns to its original dimensions when the external force is removed. As stresses increase, Young's modulus may no longer remain constant but decrease, or the material may either flow, undergoing permanent deformation, or finally break.

      When a metal bar under tension is elongated, its width is slightly diminished. This lateral shrinkage constitutes a transverse strain that is equal to the change in the width divided by the original width. The ratio of the transverse strain to the longitudinal strain is called Poisson's ratio. The average value of Poisson's ratio for steels is 0.28, and for aluminum alloys, 0.33. The volume of materials that have Poisson's ratios less than 0.50 increase under longitudinal tension and decrease under longitudinal compression.

* * *


Universalium. 2010.

Игры ⚽ Поможем написать реферат

Look at other dictionaries:

  • Young's modulus — Modulus Mod u*lus, n.; pl. {Moduli}. [L., a small measure. See {Module}, n.] (Math., Mech., & Physics) A quantity or coefficient, or constant, which expresses the measure of some specified force, property, or quality, as of elasticity, strength,… …   The Collaborative International Dictionary of English

  • Young's modulus — Young s modulus. См. Модуль Юнга. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

  • Young's modulus — yəŋz n the ratio of the tensile stress in a material to the corresponding tensile strain …   Medical dictionary

  • Young's modulus — In solid mechanics, Young s modulus (E) is a measure of the stiffness of an isotropic elastic material. It is also known as the Young modulus, modulus of elasticity, elastic modulus (though Young s modulus is actually one of several elastic… …   Wikipedia

  • Young’s modulus — tampros modulis statusas T sritis Standartizacija ir metrologija apibrėžtis Statmenojo įtempio ir santykinės ilginės deformacijos dalmuo, t. y. E = σ/ε; čia σ – statmenasis įtempis, ε – santykinė ilginė deformacija. atitikmenys: angl. coefficient …   Penkiakalbis aiškinamasis metrologijos terminų žodynas

  • Young's modulus — /jʌŋz ˈmɒdʒələs/ (say yungz mojuhluhs) noun the modulus of elasticity of a material in tension or compression, equal to the ratio of the stress applied to a wire or rod of the material to the longitudinal strain produced. {named after Thomas… …  

  • Young's modulus — noun a coefficient of elasticity applicable to the stretching of a wire • Hypernyms: ↑coefficient of elasticity, ↑modulus of elasticity, ↑elastic modulus …   Useful english dictionary

  • Young's modulus — noun The coefficient of elasticity of a solid; the rate of change of stress with strain. Syn: modulus of elasticity …   Wiktionary

  • Young's modulus — noun Physics a measure of elasticity, equal to the ratio of the stress acting on a substance to the strain produced. Origin C19: named after the English physicist Thomas Young …   English new terms dictionary

  • Modulus Guitars — is an American manufacturer of musical instruments, most notably bass guitars built with carbon fiber necks. The company, originally called Modulus Graphite, was founded in part by Geoff Gould, a bassist who also worked for an aerospace company… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”